Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button. Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.
You are now in Service mode.
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a rest
Resetting Canon BJ F900, F890, F700, F500, S900, S820, S750 and S520
Posted on Thursday, April 30, 2009
by khabibkhan
Resetting Canon PIXMA iP1000
Posted on
by khabibkhan
Waste Ink Counter Reset Manual for Service mode
- Turn off the printer. And disconnect the printer cable.
- Press and hold the POWER button, turn on the printer.
- The indicator (L.E.D.) should be green.
- Press and release the RESUME button , the indicator (L.E.D.) should be orange.
- Press and release the RESUME button again, the indicator (L.E.D.) should be green.
- Release both buttons.
Canon GENERIC “S” SERIES RESET CODE
Posted on
by khabibkhan
- Turn off the printer.
- Press and hold the RESUME button, then press and hold the POWER button.
- Release the RESUME button, Next press and release the RESUME button two(2) more times in succession. Note: you are still holding the POWER button). The printer’s carriage will “reset” or move momentarily. If the above was properly performed the printer will enter the “Service Mode”.
- Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp will alternate (change) color with each key press.
- Service/Factory test printout, including ink sensor check.
- EEPROM - Info printout.
- EEPROM - Initialization.
- Reset the Waste ink counter.
- Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!) After selecting the desired mode
- press the POWER button to “set” the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.
Resseting Printer Canon BJC-2000 BJC-2100 Series
Posted on
by khabibkhan
- Remove the Cartridge
- Unplug the AC Power Cord
- Close Front access panel, Hold down the RESUME/RESET button and plug in the AC power cord
- Release RESUME/RESET after plugging in the AC Power cord.
- Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .
- Press and HOLD RESUME/RESET for two seconds or more and release it.
- Press and HOLD RESUME/RESET for two seconds or more and release it.
- Unplug AC Power Cord to set data.
Good Luck Read More..
Reset Printer Canon i320, i255
Posted on Monday, April 20, 2009
by khabibkhan
Waste Ink Counter Reset.
Step 1 : Manual Temporary
- Unplug power and USB.
- Open door and hold power button.
- Connect power.
- Close door, then release power button.
or Step 1: Manual Temporary
- Turn off the printer. And disconnect the printer cable.
- Press and hold the POWER button, turn on the printer.
- The indicator (L.E.D.) should be green.
- Press and release the RESUME button , the indicator (L.E.D.) should be orange.
- Press and release the RESUME button again, the indicator (L.E.D.) should be green.
- Release both buttons.
step 2 : Software for Permanant
- Reconnect the printer cable.
- Open General Tools software and select (USB PORT)
- Choose (SET DESTINATION 1) And it should be reset.
Remark “After service mode Pls use software for permanent reset” Read More..
Resetting Printer Canon i850, i950, S600
Posted on Wednesday, April 15, 2009
by khabibkhan
Start with the printer OFF
1. Hold down RESUME and then hold down POWER
2. release RESUME
3. press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute:
presses - light color - function
Number of presses - light color - function
0 presses - green - Test print (or exit service mode on i960)
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses - green - EEPROM initialize
3 presses - orange - Reset waste ink counter
Subscribe to:
Posts (Atom)